OLANDIR VERCINO CORREA
27 resultados
Resultados de Busca
Agora exibindo 1 - 10 de 27
Resumo IPEN-doc 22806 Influência da corrosão no aço inoxidável duplex em solução de cloreto concentrado2001 - NETO, MOISES A.M.; DEUS, ENIO P. de; COSTA, I.; CORREA, O.V.; SOBRAL, ANA V.C.Os aços inoxidáveis duplex (AID) são ligas com duas fases, uma austenítica e outra ferrítica. Estes aços apresentam uma atrativa combinação de boas propriedades mecânica com excelente resistência à corrosão, dependendo da concentração de cloreto e da faixa de temperatura trabalhada. Esses aços são amplamente utilizados na indústria química e petroquímica devido à habilidade deste grupo de materiais em se passivar, e permanecer no estado passivo em diversos meios a que são expostos. No presente trabalho será estudado o comportamento da corrosão do aço duplex UNSS 31803. O meio eletroquímico utilizado foi o cloreto de cálcio (CaCl2 3%), visto que esse meio é bastante agressivo para os aços inoxidáveis em geral. Os ensaios eletroquímicos utilizados para se avaliar o comportamento de corrosão deste aço foram ensaios de polarização potenciodinâmica. Foi também realizado um ensaio cíclico de névoa salina, com períodos de umidificação e secagem, com o objetivo de acelerar os efeitos das intempéries climáticas típicas de uma atmosfera marítima. Para o ensaio de fratura foi utilizado o ensaio de impacto Charpy. Análises microestruturais das amostras foram realizadas através da microscopia ótica e microscopia eletrônica de varredura (MEV) e pela energia dispersiva de raios-X (EDAX). A microestrutura do material está mostrada na figura 1 em diferentes aumentos. A microestrutura apresenta duas fases distintas: austenita (fase clara) e ferrita ( fase escura) e a orientação dos grãos apresenta-se de forma transversal devido ao processo de laminação.Artigo IPEN-doc 27389 Surface chemistry and semiconducting properties of passive film and corrosion resistance of annealed surgical stainless steel2020 - OLIVEIRA, RODRIGO K. de; CORREA, OLANDIR V.; OLIVEIRA, MARA C.L. de; ANTUNES, RENATO A.ASTM F-139 surgical stainless steel was subjected to annealing treatments at 700 °C for different times. The effect of annealing on the chemical composition of the passive film was evaluated by x-ray photoelectron spectroscopy. The correlation of the surface chemistry with the corrosion behavior and semiconducting properties of the passive film was also investigated. Potentiodynamic polarization tests were conducted in phosphate-buffered solution at 37°C. The semiconducting character of the passive film was assessed by the Mott–Schottky approach. The microstructure of the annealed samples was characterized by optical microscopy. The grain size increased after annealing, but the differences between each annealing condition were not significant and could not be associated with the corrosion behavior of the annealed samples. The corrosion resistance was improved depending on the heat treatment condition due to compositional changes of the passive film upon annealing. The best corrosion properties were observed after annealing for 8 h which was ascribed to Cr2O3, MoO3 and FeO enrichment in the passive film.Artigo IPEN-doc 26756 Análise eletroquímica de um biomaterial revestido por TiO22019 - PIERETTI, E.; BORAZANIAN, T.; CORREA, O.; PILLIS, M.; ANTUNES, R.O presente trabalho avaliou, por técnicas eletroquímicas, superfícies do aço inoxidável austenítico ISO 5832-1 recobertas com filmes de TiO2, sintetizados pelo método sol-gel. As técnicas eletroquímicas utilizadas foram: monitoramento de potencial de corrosão em circuito aberto em função do tempo de imersão em solução de Ringer, que simula os fluidos corpóreos; espectroscopia de impedância eletroquímica e cálculo de densidades de dopantes no filme passivo por meio da abordagem de Mott-Schottky. Amostras deste mesmo biomaterial sem recobrimento foram analisadas para fins de comparação. Os resultados indicaram diminuição da susceptibilidade à corrosão localizada nas amostras recobertas por TiO2, devido ao caráter aderente e protetor dos filmes depositados nas superfícies deste biomaterial.Artigo IPEN-doc 26435 Effect of oxygen partial pressure on oxidation behavior of ferritic stainless steel AISI 441 at high temperatures2019 - SALGADO, MARIA de F.; CARVALHO, IURE S.; SANTOS, RAFAEL S.; PORTO, JOÃO A.S.; CORREA, OLANDIR V.; RAMANATHAN, LALGUDI V.; BRANDIM, AYRTON de S.; LINS, VANESSA F.C.In this investigation the oxidation behavior of AISI 441 stainless steel (SS) in the range from 850 °C to 950 °C was determined during 50 h in two different atmospheres: (a) synthetic air in a tubular oven; (b) argon with 1 ppm of O2 in a thermal balance. The oxidation kinetics was determined from the measured mass change as a function of oxidation time. Examination of the microstructure of the oxides and determination of their chemical composition were performed by using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and glancing angle X-ray diffraction (GAXRD). Chemical analyses showed that films formed on the AISI 441 steel surface consisted mostly of chromium oxide but manganese, iron, titanium and silicon oxides were found in the oxidized layer. In synthetic air, the steel oxidation rate increased gradually as the temperature increased, but in the argon atmosphere with 1 ppm of oxygen, the highest oxidation rate was observed at 900 °C and the lowest at 950 °C.Artigo IPEN-doc 25743 Corrosion characterization of AISI 304 stainless steel filter2018 - BARBOSA, L.P.; CORREA, O.V.; KARSOKAS FILHO, N.; COSTA, I.Pre-sintering for removal of lubricants is one of the most important steps in processing of powder metallurgy materials to achieve corrosion resistance. This is often the most neglected step in the sintering process. Incomplete removal of these organic compounds may result in sensitization of sintered parts. The aim of this study is to investigate the effect of lubricant removal process on the corrosion resistance of sintered AISI 304 L stainless steel filters. Pre-sintering was carried out at 450° C and sintering at 1150° C. As lubricant, 1% wax was used. The corrosion resistance of sintered samples was evaluated by polarization and tests, optical and scanning electron microscopy. The results showed that lubricant removal was not complete and during sintering sensitization of the stainless steel occurred decreasing the localized corrosion resistance of the stainless steel.Artigo IPEN-doc 25559 Oxidação do aço inoxidável ABNT 5601 - grau 409 em altas temperaturas em atmosfera de argônio2018 - SERRA, EDIOMAR C.; BRANDIM, AYRTON de S.; SANTOS, DIEGO M. dos; CORREA, OLANDIR V.; RAMANATHAN, LAUGUDI V.; SALGADO, MARIA de F.Aços inoxidáveis são ligas ferrosas resistentes à corrosão, devido seu alto teor de cromo. São utilizadas em ambientes com gases agressivos em altas temperaturas especialmente na indústria e aplicações tecnológicas. O objetivo desta pesquisa é investigar a cinética de crescimento e a composição de filmes do óxido formados sobre o aço ABNT 5601 - grau 409 entre as temperaturas 850 °C e 950 °C, na atmosfera de argônio, contendo 1ppm de O2. As amostras foram oxidadas em uma termobalança, com sensibilidade de ± 1 μg, por 43,4 horas de exposição. A cinética de crescimento dos filmes de óxidos foi estabelecida medindo-se o ganho de massa por unidade de área versus tempo de oxidação seguindo uma lei parabólica. A microestrutura e a composição química dos óxidos foram analisadas por microscopia eletrônica de varredura, espectroscopia dispersiva de energia. Análises químicas descrevem que os filmes formados sobre o aço ABNT 5601 - grau 409 nas diferentes temperaturas em argônio contêm o cromo como elemento majoritário além do Mn, Fe, Ti. Ao se comparar as taxas de oxidação, nas diferentes temperaturas, entre 850 e 950 °C observa-se que o aço apresenta maior taxa de oxidação a 850 °C e menor a 950 ºC.Capítulo IPEN-doc 25247 Electrochemical characterization of an optical fiber laser-treated biomaterial2018 - PIERETTI, EURICO F.; CORREA, OLANDIR V.; PILLIS, MARINA F.; NEVES, MAURICIO D.M. dasThe implant manufacturing process includes texturization to enhance its adhesion and marking the final products for their identification, long-term quality control and traceability. Marking is carried out after cleaning and prior to sterilization. These marks eventually can concentrate stress leading to premature failure. The marked areas are defective regions that affect the passive film formed on the metallic biomaterials used for implants favoring the onset of various corrosion types, such as pitting, crevice or fatigue. This study aims to evaluate the effect of a Yb optical fiber laser marking processes used for metallic implants on the localized corrosion resistance of the austenitic stainless steel ISO 5832-1. This is one of the most used materials for manufacturing implants. The electrochemical behavior of the marked areas obtained by this method was evaluated in a phosphate- buffered saline (PBS) solution with pH of 7.4 and the results were compared with unmarked samples. All tested surfaces were prepared according to the recommendations for the use in surgery. For localized corrosion resistance evaluation, electrochemical tests such as monitoring the open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and cyclic potentiodynamic polarization measurements were performed. The results showed that the laser marks affect the protector characteristics of the biomaterial’s passive film. Lower pitting resistance was associated to the laser marked areas.Resumo IPEN-doc 22163 Comparative analysis of behavior of oxidation ferritic steel AISI 439 in high temperatures in atmospheres argon and air synthetic2015 - SALGADO, MARIA F.; PORTO, JOAO A.S.; EANES, GISCARD; CORREA, OLANDIR V.; RAMANATHAN, LALGUDI V.; BRANDIM, AYRTON de S.Artigo IPEN-doc 20836 Effect of laser parameters on the corrosion resistance of the ASTM F139 stainless steel2015 - PIERETTI, EURICO F.; PESSINE, ELISABETE J.; CORREA, OLANDIR V.; ROSSI, WAGNER de; NEVES, MAURICIO D.M. dasResumo IPEN-doc 20569 Feasibility of niobium oxide-based films to prevent corrosion of AISI 304 stainless steel in nuclear fuel reprocessing plants2014 - CORREA, OLANDIR V.; OLIVEIRA, MARA C.L. de; ANTUNES, RENATO A.; SAIKI, MITIKO; SILVA JUNIOR, OSWALDO P.V. da; PILLIS, MARINA F.
- «
- 1 (current)
- 2
- 3
- »