MARIANA XAVIER MILAGRE

MARIANA XAVIER MILAGRE

Página do item completo

Resultados de Busca

Agora exibindo 1 - 8 de 8

A historical, statistical and electrochemical approach on the effect of microstructure in the anodizing of Al alloys
2023 - ARAUJO, JOAO V. de S.; MILAGRE, MARIANA; COSTA, ISOLDA
Anodizing is a well-documented surface treatment that is inserted in a complex protection system against corrosion applied to Al alloys. In the scientific literature, there are many works about this topic, which are concentrated on: (1) anodic aluminum oxide (AAO) growth mechanism; (2) anodized alloys corrosion behavior, or (3) the influence of anodizing parameters on the following steps of corrosion protection of the anodized layer. However, the effect of the microstructure on the AAO formation is not yet well established. This paper aims to review the effect of the microstructure of Al and its alloys on the anodizing process by a historical, statistical, and electrochemical approach, considering the advantages in understanding the influence of intermetallics in this process. Besides, this review brings a comparison among the number of publications and the types of alloys studied by statistical analyses. Finally, it emphasizes the importance of anodizing in the aeronautical industry, in which a great number of studied alloys are applied, mainly the 2XXX (Al-Cu) and 7XXX (AlZn) series alloys.
Corrosion behaviour of the 2098-T351 Al–Cu–Li alloy after different surface treatments
2022 - BARBOZA, WANESSA das G.; MILAGRE, MARIANA X.; DONATUS, UYIME; MACHADO, CARULINE de S.C.; RAMIREZ, OSCAR M.P.; ARAUJO, JOAO V. de S.; SILVA, REJANE M.P. da; COSTA, ISOLDA
The effect of different surface treatments on the corrosion resistance of the AA2098 Al–Cu–Li alloy has been investigated. Surface characterization was performed using 3D optical profilometry, energy dispersive X-ray spectroscopy and scanning electron microscopy. The corrosion resistance of the 2098 alloy after the surface treatments was investigated in 0.1 mol L−1 NaCl solution by electrochemical techniques and microscopy. Corrosion results showed that the untreated and the chemically etched surfaces were more active than the mechanically abraded and mechanically polished surfaces owing to differences in the nature of the native oxides formed after the surface treatments. Corrosion rate and mode were also affected by how close the exposed surface was to the mid-thickness region of the AA2098-T351 plate relative to the actual top surface (before polishing). This is associated with the variation in the volume fraction and distribution of the T1 phase as the mid-thickness region of the AA2098-T351 plate is approached.
Influence of chloride ions concentration on the development of severe localised corrosion and its effects on the electrochemical response of the 2198-T8 alloy
2021 - MACHADO, CARULINE de S.C.; SILVA, REJANE M.P. da; ARAUJO, JOAO V. de S.; MILAGRE, MARIANA X.; DONATUS, UYIME; VIVEIROS, BARBARA V.G. de; KLUMPP, RAFAEL E.; COSTA, ISOLDA
The development of severe localised corrosion (SLC) on the 2198-T8 alloy was investigated in solutions of various NaCl concentrations (0.001, 0.005 and 0.01 mol L−1). Immersion tests, optical profilometry, conventional and local electrochemical analyses were performed to evaluate the corrosion behaviour of the alloy. Immersion tests showed that the alloy is susceptible to SLC in all conditions, although the pits sizes were dependent on the solution concentration. The largest anodic areas, corresponding to SLC sites, were observed for the sample immersed in 0.001 mol L−1 NaCl, whereas pits with similar sizes were observed for the samples immersed in solutions with 0.005 and 0.01 mol L−1 of NaCl. Moreover, the maximum depth of attack was observed for the sample immersed in 0.001 mol L−1 NaCl. These results were in agreement with the scanning ionselective electrode technique (SIET) maps which showed stronger acidification on the sample exposed to 0.001 mol L−1 NaCl solution.
Correlating the modes of corrosion with microstructure in the friction stir welded AA2198-T8 alloy in aqueous hydrogen peroxide-chloride medium
2019 - MACHADO, CARULINE de S.C.; DONATUS, UYIME; MILAGRE, MARIANA X.; MOGILI, NAGA V.V.; GIORJÃO, RAFAEL A.R.; KLUMPP, RAFAEL E.; ARAUJO, JOAO V. de S.; FERREIRA, RAPHAEL O.; COSTA, ISOLDA
In this study, different types of localized corrosion in the friction stir welding (FSW) zones of an AA2198-T8 when the alloy is subjected to a corrosion test in a hydrogen peroxide–chloride solution (according to ASTM G110 standard) has been investigated. The corrosion modes were correlated with microstructure, especially with respect to the T1 phase and coarse Al-Cu-Fe phase distribution across the weldment. Simulated thermal profile and microhardness measurements were used to establish the variations in T1 phase distribution. Two types of corrosion were observed in the FSW zones: intense pitting and intergranular corrosion—type I; and the formation of cavities and trenches—type II. Type I is associated with the T1 phase while type II is associated with Al-Cu-Fe coarse intermetallics. Both types were found on the base metal (BM) and heat affected zone, but the type I reduced in the latter toward the stir zone (SZ). The SZ/thermomechanically affected zone (TMAZ) exhibited only type II. Also, Cu enrichment was observed around the type II sites in the SZ/TMAZ. Furthermore, an inverse correlation between microhardness and corrosion resistance which was related to T1 phase concentration in the different zones was also observed. Moreover, the SZ and BM were isolated and evaluated by an immersion test and electrochemical analysis using the ASTM G110 test solution. The results indicated galvanic coupling effects, as the SZ was strongly attacked when exposed separately compared to when it was coupled with the other zones.
The local electrochemical behavior of the AA2098‐T351 and surface preparation effects investigated by scanning electrochemical microscopy
2019 - SILVA, REJANE M.P. da; MILAGRE, MARIANA X.; OLIVEIRA, LEANDRO A. de; DONATUS, UYIME; ANTUNES, RENATO A.; COSTA, ISOLDA
In this work, scanning electrochemical microscopy (SECM) measurements were employed to characterize the electrochemical activities on polished and as‐received surfaces of the 2098‐T351 aluminum alloy (AA2098‐T351). The effects of the near surface deformed layer (NSDL) and its removal by polishing on the electrochemical activities of the alloy surface were evaluated and compared by the use of different modes of SECM. Confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM) were also employed to characterize the morphology of the surfaces. The surface chemistry was analyzed by X‐ray photoelectron spectroscopy (XPS). The surface generation/tip collection (SG/TC) and competition modes of the SECM were used to study hydrogen gas (H2) evolution and oxygen reduction reactions, respectively. H2 evolution and oxygen reduction were more pronounced on the polished surfaces. The feedback mode of SECM was adopted to characterize the electrochemical activity of the polished surface that was previously corroded by immersion in a chloride‐containing solution, in order to investigate the influence of the products formed on the active/passive domains. The precorroded surface and as‐received surfaces revealed lower electrochemical activities compared with the polished surface showing that either the NSDL or corrosion products largely decreased the local electrochemical activities at the AA2098‐T351 surfaces.
Effect of surface treatments on the localized corrosion resistance of the AA2198‐T8 aluminum lithium alloy welded by FSW process
2019 - MACHADO, CARULINE de S.C.; KLUMPP, RAFAEL E.; AYUSSO, VICTOR H.; DONATUS, UYIME; MILAGRE, MARIANA X.; ARAUJO, JOAO V. de S.; MACHADO, GLAUSON A.F.; COSTA, ISOLDA
In this work, the effect of eight types of surface treatments on the corrosion resistance of friction stir welded samples of an AA2198‐T8 Al‐Cu‐Li alloy were tested and compared in an attempt to find suitable alternatives to toxic and carcinogenic hexavalent chromium treatments. All the samples were anodized and subjected to different post‐anodizing treatments. The post‐anodizing treatments were (1) hydrothermal treatment in Ce (NO3)3 6H2O solution; (2) hydrothermal treatment in Ce (NO3)3 6H2O solution with H2O2; (3) hydrothermal treatment in boiling water; (4) hexavalent chromium conversion coating; and (5) immersion in BTSE (bis‐1,2‐(triethoxysilyl) ethane. The corrosion resistance of the treated samples was evaluated by immersion tests in sodium chloride solution (0.1 mol L−1 NaCl) and electrochemical impedance spectroscopy (EIS) of the friction stir weldment. The results showed that among the alternative treatments, the Ce‐containing solutions presented the best corrosion resistance, especially when used without peroxide.
The effect of surface pretreatment on the corrosion behaviour of silanated AA2198‐T851 Al‐Cu‐Li alloy
2019 - DONATUS, UYIME; KLUMPP, RAFAEL E.; MOGILI, NAGA V.V.; ANTUNES, RENATO A.; MILAGRE, MARIANA X.; COSTA, ISOLDA
The corrosion behaviour of silanated AA2198‐T851 alloy substrates with and with no manufacturing‐process induced near‐surface deformed layer (MPI‐NSDL) has been investigated. Two methods (alkaline etching + desmutting and mechanical polishing) were employed in removing the MPI‐NSDL. Silanization was performed using 2‐bistriethoxysilylethane. Electrochemical impedance spectroscopy (EIS), salt spray test, and microscopy techniques were employed in the investigation of the corrosion behaviours. The studies revealed that polishing appeared to be the best silanating pre‐treatment (compared with degreasing and etching + desmutting) for the new generation AA2198‐T851 Al‐Cu‐Li alloy, and this was reflected in the EIS spectra. The etched + desmutted and the degreased surface with MPI‐NSDL did not respond well to silanization and presented more pitting sites per square millimeter. However, the severity of corrosion per pit was more on the polished sample compared with the other two. Also, the corrosion mechanisms were different for the three cases.
Comparison of the corrosion resistance of an Al–Cu alloy and an Al–Cu–Li alloy
2019 - MILAGRE, MARIANA X.; DONATUS, UYIME; MACHADO, CARULINE S.C.; ARAUJO, JOAO V.S.; SILVA, REJANE M.P. da; VIVEIROS, BARBARA V.G. de; ASTARITA, ANTONELLO; COSTA, ISOLDA
In this study, the corrosion mechanisms of the AA2024-T3 and the AA2098-T351 were investigated and compared using various electrochemical techniques in 0.005 mol L−1 NaCl solution. The severe type of corrosion in the AA2098-T351 was intragranular attack (IGA) although trenching and pitting related to the constituent particles were seen. On the other hand, the AA2024-T3 exhibited severe localised corrosion associated with micrometric constituent particles, and its propagation was via grain boundaries leading to intergranular corrosion (IGC). Electrochemical techniques showed that the corrosion reaction in both alloys was controlled by diffusion. The non-uniform current distribution in both alloys showed that EIS was not a proper technique for comparing the corrosion resistance of the alloys. However, local electrochemical techniques were useful for the evaluation of the corrosion resistance of the alloys.