ANSELMO FEHER

ANSELMO FEHER

(Fonte: Lattes)

Resumo

Graduado em Tecnologia Mecânica com ênfase em soldagem pela Faculdade de Tecnologia de São Paulo (1992), possui mestrado em Tecnologia Nuclear pela Universidade de São Paulo (2006) e doutorado em Tecnologia Nuclear pela Universidade de São Paulo (2014). Atualmente é Servidor Público Federal da Comissão Nacional de Energia Nuclear, órgão vinculado ao Ministério da Ciência, Tecnologia e Inovação. Tem experiência nas áreas de Engenharia Mecânica e Aplicações Nucleares, atuando principalmente em desenvolvimento e manutenção de sistemas de alto vácuo, ensaios de detecção de vazamentos utilizando espectrômetros de massa para gás hélio, produção de fontes radioativas seladas, soldagem por arco plasma, soldagem a laser, braquiterapia, sementes de iodo-125 e fontes de irídio-192 para tratamento de câncer. (Texto extraído do Currículo Lattes em 28 mar. 2023)

Lattes

Página do item completo

Resultados de Busca

Agora exibindo 1 - 10 de 23

Electron beam processing to improve biodegradable polymers and for industrial wastewater treatment and recycling
2022 - CALVO, W.A.P.; MUNHOZ, P.M.; SOMESSARI, S.L.; DUARTE, C.L.; SPRENGER, F.E.; FEHER, A.; LAINETTI, F.F.; GASPAR, R.R.; NASCIMENTO, F.C.; SILVA, L.G.A.; HARADA, J.; BRAGA, A.; RODRIGUES, M.; SAMPA, M.H.O.
Radiation technology has been used to control environmental pollution. The aim of these studies was to apply the electron beam radiation technology for controlling plastic pollution and environmental protection.
Development and construction of a mobile electron beam accelerator to treat and recycle industrial effluents in Brazil
2022 - CALVO, WILSON A.P.; SOMESSARI, SAMIR L.; DUARTE, CELINA L.; SPRENGER, FRANCISCO E.; FEHER, ANSELMO; LAINETTI, FABIANA de F.; GASPER, RENATO R.; BRAGA, ALCIDES; RODRIGUES, MARCOS; SAMPA, MARIA H.O.
In the world, there is a growing increase in the demand for water for human consumption, as well as the prioritization of the use of available water resources for public supply. The treatment of wastewater and industrial effluents by electron beam irradiation is a promising technique, however, not very widespread in Brazilian territory. The design and construction of a mobile unit by the Nuclear and Energy Research Institute (IPEN/CNEN), containing an electron beam accelerator of 0.7 MeV, 20 kW and 640 mm window is innovative to demonstrate the effects and positive results of this technology. The mobile unit will have as one of its main advantages the possibility of treating effluents in the place where the source is located, eliminating costs and bureaucratic problems associated with the transportation of waste, besides publicizing the technology in several places in the country. To implement the project, IPEN/CNEN has been consolidating partnerships with national and international companies. The resources for the development of the unit have been supplied by the Brazilian Innovation Agency (FINEP) and International Atomic Energy Agency, financing the “IAEA TC Project BRA1035 - Mobile electron beam accelerator to treat and recycle industrial effluents”. The Institute has associated with a specialized company (Truckvan Industry) in an innovation project for the unit design and development. Several meetings have been realized with the company and the International Atomic Energy Agency experts, aiming the compatibility of the design and the exchange of information necessary for the project development. The idealized project divides the cart in the following modules: a) control room and laboratory for technical and scientific dissemination of the technology; b) industrial electron beam accelerator, hydraulic units, ventilation system, cooler and bunker with irradiation device; and c) transformer and power source supply. A 3D model study of the control room and laboratory space was done to facilitate understanding the internal distribution of the laboratory analysis equipment (Gas Chromatography Mass Spectrometry, Total Organic Carbon and UV-Visible Spectroscopy). The irradiation system with electron accelerators allows treating different types of effluents. Depending on the effluent, the amount of ionizing radiation energy required for treatment may vary, as well as the amount of treated effluent per day. For the construction of the mobile unit, the estimated cost is about US$ 1.5 Million. The type of treated effluent, the treatment cost per m3/day and other information regarding the cost of maintenance and operation of the mobile unit are obtained from the Business Plan of the Mobile Unit.
Development of an irradiation system for production of gaseous radioisotopes and of a tomographic 2-D gamma scanning for industrial process troubleshooting in Brazil
2022 - CARDOZO, NELSON X.; HARAGUCHI, MARCIO I.; KIM, HAE Y.; SOMESSARI, SAMIR L.; FEHER, ANSELMO; NAPOLITANO, CELIA M.; CALVO, WILSON A.P.
Radioisotopes as radiotracers are used in analytical procedures to obtain qualitative and quantitative data systems, in physical and physicochemical studies transfers, and troubleshooting of industrial process plants in chemical and petrochemical companies. In the production of gaseous radioisotopes used as tracers in industrial process measurements, argon-41 (41Ar) and krypton-79 (79Kr) stand out because each has low reactivity with other chemical elements. 41Ar is a transmitter range with high-energy (1.29 MeV) and a high percentage of this energy transformation (99.1%), resulting in relatively small quantities required in relation to the other, for an efficient detection, even in large thicknesses components. In this sense, the aim of this study is to develop an irradiation system for gaseous radioisotope production in continuous scale, applied in industrial applications of emission tomography and flow measurement. The irradiation system may produce 41Ar with activity of 7.4×1011 Bq (20 Ci) per irradiation cycle, through the Reactor IEA-R1 with 4.5 MW and average thermal neutron flux of 4.71×1013 ncm−2s−1 to meet an existing demand in NDT and inspections companies, and even needed by the Radiation Technology Centre, at IPEN/CNEN. The irradiation system consists of an aluminium irradiation capsule, transfer lines, needle valves, ringed connections, quick connectors, manometer, vacuum system, dewar, lead shielding, storage and transport cylinders, among other components. The irradiation system was approved in the leakage and stability tests (bubble test, pressurization, evacuation and with leak detector equipment. In the experimental production obtaining 1.07×1011 Bq (2.9 Ci) of 41Ar, alanine dosimeters were distributed into various components of the irradiation system. In addition, exposure rates were determined in the lead shielding wall, in which the liquefied radioactive gas was concentrated, and in the storage and transport cylinders after 41Ar was transferred by the portable radiation meter. However, gamma scanning is a nuclear inspection technique widely used to troubleshoot industrial equipment in refineries and petrochemicals plants such as distillation columns and reactors. A sealed radiation source and detector move along the equipment, and the intensity readouts generate the density profile of the equipment. The result of gamma scan still consists of a simple 1-D density plot. In this work, we also present the tomographic gamma scanning that, using image reconstruction techniques, shows the result as a 2-D image of density distribution. Clearly, an image reveals more features of the equipment than a 1-D graph and many problems that could not be troubleshooted using the conventional technique can now be solved with this imaging technique. We use ART (Algebraic Reconstruction Technique) intercalated with total variation minimization filter. The use of total variation minimization leads to compressive sensing tomography, allowing to obtain good quality reconstruction from few irradiation data. We simulated the reconstruction of different density distributions. We applied the new technique to data obtained by irradiating with gamma rays phantoms that emulate industrial equipment. Finally, we present the result obtained by applying the innovative technique to real operating distillation column.
Automation system for quality control in manufacture of iodine-125 sealed sources used in brachytherapy
2011 - SOMESSARI, SAMIR L.; FEHER, ANSELMO; SPRENGER, FRANCISCO E; ROSTELATO, MARIA E.C.M.; MOURA, JOAO A.; COSTA, OSVALDO L.; CALVO, WILSON A.P.
The aim of this work is to develop an automation system for Quality Control (QC) in the production of iodine-125 sealed sources, after undergoing the process of Laser Beam Welding (LBW). These sources, also known as iodine-125 seeds are used, successfully, in the treatment of cancer by brachytherapy, with low-dose rates. Each small seed is composed of a welded titanium capsule with 0.8 mm diameter and 4.5 mm in length, containing iodine-125 adsorbed on an internal silver wire. The seeds are implanted in the human prostate to irradiate the tumor and treat the cancerous cells. The technology to automate the quality control system in the manufacturing of iodine-125 seeds consists in developing and associate mechanical parts, electronic components and pneumatic circuits to control machines and processes. The automation technology for iodine-125 seed production developed in this work employs Programmable Logic Controller (PLC), step motors, drivers of control, electrical-electronic interfaces, photoelectric sensors, interfaces of communication and software development. Industrial automation plays an important role in the production of Iodine-125 seeds, with higher productivity and high standard of quality, facilitating the implementation and operation of processes with Good Manufacturing Practices (GMP). Nowadays, the Radiation Technology Center at IPEN-CNEN/SP imports 36,000 iodine-125 seeds per year and distributes them for clinics and hospitals in the country. However, the Brazilian potential market is of 8,000 iodine-125 seeds per month. Therefore, the local production of these radioactive seeds has become a priority for the Institute, aiming to reduce the price and increase the supply to the population in Brazil.
Developing an electrical power system of a mobile electron beam accelerator to treat wastewater and industrial effluents
2021 - GASPER, RENATO R.; SOMESSARI, SAMIR L.; SPRENGER, FRANCISCO E.; FEHER, ANSELMO; DUARTE, CELINA L.; SAMPA, MARIA H. de O.; LAINETTI, FABIANA de F.; BRAGA, ALCIDES; RODRIGUES, MARCOS de M.; CALVO, WILSON A.P.
The treatment of wastewater and industrial effluents by electron beam irradiation is a promising technique, however, not very widespread in Brazilian territory. The design and construction of a mobile unit by the Nuclear and Energy Research Institute, containing an electron beam accelerator of 700 keV and 20 kW is innovative to demonstrate the effects and positive results of this technology. The aim is to transfer the mobile unit to several companies with interest in liquid waste treatment, connect to the industry electrical system and start the ionization treatment process through electron beam. The mobile unit connection to the local electrical system may be a challenge due to the great diversity of voltages and distances involved, as well as the large injections of harmonic content generated by the electron beam accelerator that can affect sensitive loads in the industrial system. In this work, an analysis of the electrical power system of the mobile unit was made, regarding the interruption capacity, selectivity protection and adequate short circuit levels, in order to assure a greater reliability in the operation. At the end, the control panel of the mobile unit, simulations and measurements were carried out at the 1.5 MeV and 37.5 kW electron beam accelerator, installed in the Radiation Technology Center, demonstrating the necessity of applying a filter to reduce the measured harmonic distortion. The analysis of the mobile unit electrical power system was made, in order to assure a greater reliability in the operation.
Developing an electrical power system of a mobile electron beam accelerator to treat wastewater and industrial effluents
2019 - GASPAR, R.R.; SOMESSARI, S.L.; SPRENGER, F.E.; FEHER, A.; DUARTE, C.L.; SAMPA, M.H.O.; LAINETTI, F.F.; FUGA, D.F.; RODRIGUES, M.; CALVO, W.A.P.
The treatment of wastewater and industrial effluents by electron beam irradiation is a promising technique, however, not very widespread in Brazilian territory. The design and construction of a mobile unit by the Nuclear and Energy Research Institute, containing an electron beam accelerator of 700 keV and 20 kW is innovative to demonstrate the effects and positive results of this technology. The aim is to transfer the mobile unit to several companies with interest in liquid waste treatment, connect to the industry electrical system and start the ionization treatment process through electron beam. The mobile unit connection to the local electrical system may be a challenge due to the great diversity of voltages and distances involved, as well as the large injections of harmonic content generated by the electron beam accelerator that can affect sensitive loads in the industrial system. In this work, an analysis of the electrical power system of the mobile unit was made, regarding the interruption capacity, selectivity protection and adequate short circuit levels, in order to assure a greater reliability in the operation. At the end, the control panel of the mobile unit, simulations and measurements were carried out at the 1.5 MeV and 37.5 kW electron beam accelerator, installed in the Radiation Technology Center, demonstrating the necessity of applying a filter to reduce the measured harmonic distortion. The analysis of the mobile unit electrical power system was made, in order to assure a greater reliability in the operation.
Architectural design of a mobile irradiation unit for the treatment of industrial effluents in Brazil
2019 - LAINETTI, F.F.; DUARTE, C.L.; SOMESSARI, S.L.; SPRENGER, F.E.; FEHER, A.; SAMPA, M.H.O.; GASPAR, R.R.; FUGA, D.; RODRIGUES, M.; CALVO, W.A.P.
The Nuclear and Energy Research Institute (IPEN-CNEN/SP) decided to develop and build a mobile beam irradiation unit for the treatment of industrial effluents. The mobile unit will have as one of its main advantages the possibility of treating effluents in the place where the source is located, eliminating costs and bureaucratic problems associated with the transportation of waste, besides publicizing the technology in several places in Brazil. To implement the project, IPEN-CNEN/SP has been consolidating partnerships with national and international companies. The resources for the development of the unit have been supplied by the Brazilian Innovation Agency (FINEP) and International Atomic Energy Agency, financing the IAEA TC Project BRA1035 – Mobile electron beam accelerator to treat and recycle industrial effluents. The Institute hired a specialized company (Truckvan Industry) for the unit design and development. Several meetings have been realized with the company and the IAEA experts aiming the compatibility of the design and the exchange of information necessary for the project development. Regarding the mobile lab, several layout options have been developed to better meet the needs of each device and its users. The layout has been discussed with the objective of facilitating the maintenance of the equipment; the well-being and ergonomics of operators; optimization of spacing and also to make compatible the need for the presence of equipment and space for operators. Thus, several studies have been prepared to allow the discussion between the areas involved and to optimize the project, as well as the visualization of the spaces available. In this paper is presented the approach adopted for the architectural design of a mobile irradiation unit in Brazil.
Development of an irradiation system for radioisotope production applied to industrial process tomography
2016 - CARDOZO, NELSON X.; OMI, NELSON M.; AMBIEL, JOSE J.; FEHER, ANSELMO; NAPOLITANO, CELIA M.; SOMESSARI, SAMIR L.; CALVO, WILSON A.P.
Among the various applications of radioisotopes, the use of radiotracers is considered the most important in diagnosing operation and troubleshooting of industrial process plants in chemical and petrochemical companies. The radiotracers are used in analytical procedures to obtain qualitative and quantitative data systems, in physical and physicochemical studies transfers. In the production of gaseous radioisotopes used as tracers in industrial process measurements, argon-41 (41Ar) and krypton-79 (79Kr) have low reactivity with other chemical elements. 41Ar is a transmitter range with high-energy (1.29MeV) and a high percentage of this energy transformation (99.1%), resulting in relatively small quantities required in relation to the other, for an efficient detection, even in large thicknesses components. Nowadays, the production of gaseous radioisotopes in nuclear research reactors is performed in small quantities (batches), through quartz ampoules containing natural gas 40Ar or 78Kr. In this sense, the aim of this study is to develop an irradiation system for gaseous radioisotope production in continuous scale, applied in industrial applications of emission tomography and flow measurement. The irradiation system may produce 41Ar with activity of 7.4x1011Bq (20Ci) per irradiation cycle, through the Reactor IEA-R1 with 4.5MW and average thermal neutron flux of 4.71x1013 ncm-2s-1 to meet an existing demand in NDT and inspections companies, and even needed by the Radiation Technology Centre, at IPEN/CNEN-SP. The irradiation system consists of an aluminium irradiation capsule, transfer lines, needle valves, stripy connections, quick connectors, manometer, vacuum system, dewar, lead shielding, storage and transport cylinders, among other components. The irradiation system was approved in the leakage and stability tests (bubble test, pressurization, evacuation and with leak detector equipment SPECTRON 600 T). In the experimental production, alanine dosimeters were distributed into various components of the irradiation system, obtaining 1.07x1011Bq (2.9Ci) of 41Ar. In addition, exposure rates were determined in the lead shielding wall, in which the liquefied radioactive gas was concentrated, and in the storage and transport cylinders after 41Ar was transferred, by the portable radiation meter Teletector ® Probe 6150 AD-t/H.
Preliminary studies on the development of an automated irradiation system for production of gaseous radioisotopes applied in industrial processes
2019 - DOURADO, NELSON X.; OMI, NELSON M.; SOMESSARI, SAMIR L.; GENEZINI, FREDERICO A.; FEHER, ANSELMO; NAPOLITANO, CELIA M.; AMBIEL, JOSE J.; CALVO, WILSON A.P.
The purpose of the present study is to demonstrate how it will be enhanced an Irradiation System (IS) developed with national technology to produce gaseous radioisotopes, by means of the components automation, to avoid the radiation exposure rate to operators of the system, following the ALARA principle (As Low As Reasonably Achievable). Argon-41 (41Ar) and krypton-79 (79Kr) can be produced in continuous scale, gaseous radioisotopes used as radiotracers in industrial process measurements and it can be used in analytical procedures to obtain qualitative and quantitative data systems or in physical and physicochemical studies transfers. The production occurs into the IS, installed in the pool hall of a nuclear research reactor in which the irradiation capsule is positioned near the reactor core containing the isotope gaseous pressurized (40Ar or 78Kr), by (n,γ) reaction and generate the radioisotopes. After the irradiation, the gaseous radioisotope is transferred to the system and, posteriorly, to the storage and transport cylinders, that will be used in an industrial plant. In the first experimental production, was obtained 1.07x1011 Bq (2.9 Ci) of 41Ar distributed in two storage and transport cylinders, operating the IEA-R1 Research Reactor with 4.5 MW and average thermal neutron flux of 4.71x1013 n.cm-2.s-1. However, the system has capacity to five storage and transport cylinders and the estimated maximum activity to be obtained is 7.4x1011 Bq (20 Ci) per irradiation cycle. In this sense, the automation will be based in studies of the production process in the system and the use of Programmable Logic Controllers (PLC), and supervisory software allowing a remote control and consequently better security conditions.
Development of a mobile unit with an electron beam accelerator (20 kw and 700 keV)
2019 - SOMESSARI, SAMIR L.; FEHER, ANSELMO; SPRENGER, FRANCISCO E.; DUARTE, CELINA L.; SAMPA, MARIA H. de O.; OMI, NELSON M.; GASPER, RENATO R.; LAINETTI, FABIANA; FUGA, DANILO F.; RODRIGUES, MARCOS; CALVO, WILSON A.P.
The purpose of the present study is therefore to install an electron beam accelerator (20 kW and 700 keV) in a mobile unit to treat effluent from petroleum production, for petroleum desulfurization and, in addition, for degradation of toxic organic compounds in wastewater for reusein, in partnerships with private and public institutions. Several technical aspects were considered in this installation, such as following the national transport legislation and the safety requirements (BSS, IAEA and CNEN Safety Standards). Technical characteristics of the electron beam accelerator (EBA) are energy of 700 keV and 28.5 mA of beam current, with 60 cm scan length. The installation of the EBA includes the developing and manufacturing a radiological shield. In several points of the mobile unit, GM type radiation sensors will be installed for radiological monitoring during irradiation processing, interlocked with the accelerator’s safe operating system. For the design of a vacuum system with mechanical pumps, ion pump and sensors, the following procedures will be carried out: a) design of an optimized system of the mobile unit power supply; b) development of a cooling system with deionized water and pressurized air for the cooling of the EBA systems in the scan horn, high voltage generator, control panel, vacuum system, among other peripherals; c) installation of the fan to cool the thin titanium window; d) installation of an ozone filter in the exhaust system to remove gas generated during irradiation; e) project of a mechanical structural reinforcement of the trailer was studied, improved and executed. In the mobile unit, a space was created for an analysis laboratory to monitor the wastewater before and after irradiation, establishing parameters in the quality control of the irradiated material.