NIKOLAS LYMBERIS SCURO

NIKOLAS LYMBERIS SCURO

Página do item completo

Resultados de Busca

Agora exibindo 1 - 4 de 4

Preliminary numerical analysis of the flow distribution in the core of a research reactor
2019 - SCURO, NIKOLAS L.; ANGELO, GABRIEL; ANGELO, E.; TORRES, WALMIR M.; UMBEHAUN, PEDRO E.; ANDRADE, DELVONEI A. de
The thermal-hydraulic safety analysis of research reactors establishes the safety criteria to ensure the integrity of the fuel elements in the reactor core. It assures that all core components are being adequately cooled during operation. It is necessary to know if the average mass flow rate (and their standard deviation) among the fuel assemblies are enough to cool the power generated during operation. Once satisfied such condition, it allows the calculation of the maximum heat flux transferred from fuel assemblies to the coolant, and if the maximum cladding temperatures are below the limits set by the safety criteria. Among the objectives, this study presents a methodology for a preliminary three-dimensional numerical analysis of the flow distribution in the core of the IEA-R1 research reactor, under steady state condition. For this, the ANSYS-CFX® commercial code was used to analyze the flow dynamics in the core, and to visualize the velocity field. It was possible to conclude that a homogeneous flow distribution for all standard fuel assemblies were found, with 2.7% deviation from the average mass flow. What turned out to be negligible and can be assumed that there is a homogeneous distribution in the core. Complex structures were find in the computational domain. Once known the core flow dynamics, it allows future studies to determine whether the heat flux and temperature conditions abbeys thermal-hydraulic safety criteria.
Transient cfd analysis of the flow inversion of the nuclear research reactor IEA-R1
2018 - SCURO, N.L.; SANTOS, P.G.; UMBEHAUN, P.E.; ANDRADE, D.A.; ANGELO, E.; ANGELO, G.
The IEA-R1 research reactor works with a downflow direction, but after pumps shutdown during a LOFA test, the reactor shutdown. The heat decay will be removed by natural convection, which is an upward flow, originating flow inversion. Using the Instrumented Fuel Element designed at the Institute for Energy and Nuclear Research (IPEN), the loss of flow accident (LOFA) was analyzed along instrumented fuel plates. The preliminary results showed temperature peaks during inversion, which is as much representative as in nominal operation at 3.5MW. Therefore, these experimental data lead a construction and validation of a transient three-dimensional numerical analysis for a single fuel channel using the ANSYS-CFX® commercial code. The numerical results show improvement in obtaining more properties, e.g., wall heat transfer coefficient, which is usually obtained through empirical correlations.
CFD analysis of blockage length on a partially blocked fuel rod
2017 - SCURO, NIKOLAS L.; ANGELO, GABRIEL; ANGELO, EDVALDO; ANDRADE, DELVONEI A. de
In LOCA accidents, fuel rods may balloon by the increasing of pressure difference between fuel rod and core vessel. With the balloon effect, the swelling can partially block the flow channel, affecting the coolability during reflood phase. In order to analyze the influence of blockage length after LOCA events, many numerical simulations using Ansys-CFX code have been done in steady state condition, characterizing the final phase of reflood. Peaks of temperature are observed in the middle of the fuel rod, followed by a temperature drop. This effect is justified by the increasing of heat transfer coefficient, originated from the high turbulence effects. Therefore, this paper considers a radial blockage of 90%, varying just the blockage length. This study observed that, for the same boundary conditions, the longer the blockage length originated after LOCA events, the higher are the central temperatures in the fuel rod.
Experimental investigation of critical velocity in a parallel plate research reactor fuel assembly
2017 - CASTRO, ALFREDO J.A.; SCURO, NIKOLAS L.; ANDRADE, DELVONEI A.
The fuel elements of a MTR (Material Testing Reactor) type nuclear reactor are mostly composed of aluminumcoated fuel plates containing the core of uranium silica (U3Si2) dispersed in an aluminum matrix. These plates have a thickness of the order of millimeters and are much longer in relation to their thickness. They are arranged in parallel in the assembly of the fuel element to form channels between them a few millimeters in thickness, through which there is a flow of the coolant. This configuration, combined with the need for a flow at high flow rates to ensure the cooling of the fuel element in operation, may create problems of mechanical failure of fuel plate due to the vibration induced by the flow in the channels. In the case of critical velocity excessive permanent deflections of the plates can cause blockage of the flow channel in the reactor core and lead to overheating in the plates. For this study an experimental bench capable of high volume flows and a test section that simulates a plate-like fuel element with three cooling channels were developed. The dimensions of the test section were based on the dimensions of the Fuel Element of the Brazilian Multipurpose Reactor (RMB), whose project is being coordinated by the National Commission of Nuclear Energy (CNEN). The experiments performed attained the objective of reaching Miller's critical velocity condition. The critical velocity was reached with 14.5 m/s leading to the consequent plastic deformation of the flow channel plates.