OSCAR OLIMPIO DE ARAUJO FILHO
19 resultados
Resultados de Busca
Agora exibindo 1 - 10 de 19
Resumo IPEN-doc 10125 On sintering of a AISI M3:2 high speed steel2003 - ARAUJO FILHO, O.O.; NEVES, M.D.M.; AMBROZIO FILHO, F.; QUADROS, N.F.Resumo IPEN-doc 13325 Tenacidade a fratura do aco rapido do molibdenio AISI M3:2 produzido por metalurgia do po2008 - NOGUEIRA, R.A.; SANTANA da SILVA, W.; GOLDENSTEIN, H.; ARAUJO FILHO, O.O.; AMBROZIO, F.Resumo IPEN-doc 12494 Fracture toughness of a AISI M3:2 high steel produced by powder metallurgy2007 - SANTANA da SILVA, W.; GOLDENSTEIN, H.; ARAUJO FILHO, O.O.; AMBROZIO FILHO, F.Resumo IPEN-doc 11078 Sintering of AISI M3-2 high speed steel-Part II2005 - ARAUJO FILHO, O.O.; NEVES, M.D.M.; OLIVEIRA, E.E.; SILVA, L.C.E.; SALGADO, L.; AMBROZIO FILHO, F.Liquid phase sintering of high speed steels seems to be a cheaper processing route in the manufacturing of tool steels if compared to the well-known and expansive hot isostatic pressing high speed steels. In a previous work a M3:2 high speed steel was vacuum sintered from irregular water atomized powder and had its sintering temperature determined. In this work the same powder was uniaxially cold compacted and vaccum sintered by adding some small quantity of carbon (0.3% in weight) to prevent porosity and loss of carbon which result from the sintering cycle. The sintered samples from all these experimental procedures had their density evaluated. The microstructure was evaluated using optical-electronic techniques in order to investigate the best range of sintering temperature. At least five parallel samples were tested to each condition of sintering.Resumo IPEN-doc 11069 Carbide size and bend strength of M3-2 high speed tool steels2005 - ARAUJO FILHO, O.O.; RIBEIRO, O.C.S.; NOGUEIRA, R.A.; LIBERATI, J.F.; MUNIZ, L.F.; AMBROZIO FILHO, F.Artigo IPEN-doc 12600 Propriedades dos acos rapidos AISI M3:2 produzidos por metalurgia convencional e tecnicas de metalurgia do po2006 - ARAUJO FILHO, O.O.; RIBEIRO, O.C.S.; NOGUEIRA, R.A.; NEVES, M.D.M.; MUNIZ, L.F.; AMBROZIO FILHO, F.Aços rápidos AISI M3:2 produzidos por metalurgia convencional e por diferentes técnicas de metalurgia do pó são objetos desse trabalho de pesquisa. O aço rápido Sinter 23, obtido por sinterização com compactação isostática a quente, o aço rápido M3:2 obtido por compactação uniaxial a frio e sinterização com fase líquida com e sem a adição de 0,3%C (na forma de grafite) e o aço rápido convencional VWM3C foram submetidos ao tratamento térmico de endurecimento e tiveram suas propriedades de resistência à ruptura transversal, tamanho médio de carboneto primário e dureza avaliadas. Ensaios de dureza Rockwell C foram realizados para verificar o quão efetivo foi o tratamento térmico. Amostras dos aços rápidos foram fabricadas e submetidas ao tratamento térmico e rompidas em ensaios de flexão em três pontos no sentido de se determinar a resistência à ruptura transversal. As microestruturas foram avalidas por Microscopia Eletrônica de Varredura.Artigo IPEN-doc 12573 Influencia do metodo de compactação e das temperaturas e etapas de tratamento na microestrutura e dureza do aco rapido AISI T15 sinterizado a vacuo2006 - LIMA, E.P.R.; NOGUEIRA, R.A.; ARAUJO FILHO, O.O. de; NEVES, M.D.M. das; AMBROZIO FILHO, F.Artigo IPEN-doc 11061 Grain Size of commercial high speed steel2005 - NOGUEIRA, R.A.; ARAUJO FILHO, O.O.; SOUZA, L.F.M.; LIBERATI, J.F.; SALGADO, L.; AMBROZIO FILHO, F.Artigo IPEN-doc 15952 Processing of AISI M2 HSS with addition of NbC by mechanical alloying using two different types of attritor mills2009 - ARAUJO FILHO, OSCAR O. de; NEVES, MAURICIO D.M. das; GONZALEZ, CEZAR H.; URTIGA FILHO, SEVERINO L.; AMBROZIO FILHO, FRANCISCOArtigo IPEN-doc 10519 Sinterizacao do aco rapido ao molibdenio AISI M3:22004 - ARAUJO FILHO, O.O.; NEVES, M.D.M.; RIBEIRO, O.C.S.; DESIMONE, D.; NOGUEIRA, R.A.; AMBROZIO FILHO, F.