OSCAR OLIMPIO DE ARAUJO FILHO
8 resultados
Resultados de Busca
Agora exibindo 1 - 8 de 8
Resumo IPEN-doc 13325 Tenacidade a fratura do aco rapido do molibdenio AISI M3:2 produzido por metalurgia do po2008 - NOGUEIRA, R.A.; SANTANA da SILVA, W.; GOLDENSTEIN, H.; ARAUJO FILHO, O.O.; AMBROZIO, F.Resumo IPEN-doc 11069 Carbide size and bend strength of M3-2 high speed tool steels2005 - ARAUJO FILHO, O.O.; RIBEIRO, O.C.S.; NOGUEIRA, R.A.; LIBERATI, J.F.; MUNIZ, L.F.; AMBROZIO FILHO, F.Artigo IPEN-doc 12600 Propriedades dos acos rapidos AISI M3:2 produzidos por metalurgia convencional e tecnicas de metalurgia do po2006 - ARAUJO FILHO, O.O.; RIBEIRO, O.C.S.; NOGUEIRA, R.A.; NEVES, M.D.M.; MUNIZ, L.F.; AMBROZIO FILHO, F.Aços rápidos AISI M3:2 produzidos por metalurgia convencional e por diferentes técnicas de metalurgia do pó são objetos desse trabalho de pesquisa. O aço rápido Sinter 23, obtido por sinterização com compactação isostática a quente, o aço rápido M3:2 obtido por compactação uniaxial a frio e sinterização com fase líquida com e sem a adição de 0,3%C (na forma de grafite) e o aço rápido convencional VWM3C foram submetidos ao tratamento térmico de endurecimento e tiveram suas propriedades de resistência à ruptura transversal, tamanho médio de carboneto primário e dureza avaliadas. Ensaios de dureza Rockwell C foram realizados para verificar o quão efetivo foi o tratamento térmico. Amostras dos aços rápidos foram fabricadas e submetidas ao tratamento térmico e rompidas em ensaios de flexão em três pontos no sentido de se determinar a resistência à ruptura transversal. As microestruturas foram avalidas por Microscopia Eletrônica de Varredura.Artigo IPEN-doc 12573 Influencia do metodo de compactação e das temperaturas e etapas de tratamento na microestrutura e dureza do aco rapido AISI T15 sinterizado a vacuo2006 - LIMA, E.P.R.; NOGUEIRA, R.A.; ARAUJO FILHO, O.O. de; NEVES, M.D.M. das; AMBROZIO FILHO, F.Artigo IPEN-doc 11061 Grain Size of commercial high speed steel2005 - NOGUEIRA, R.A.; ARAUJO FILHO, O.O.; SOUZA, L.F.M.; LIBERATI, J.F.; SALGADO, L.; AMBROZIO FILHO, F.Artigo IPEN-doc 10519 Sinterizacao do aco rapido ao molibdenio AISI M3:22004 - ARAUJO FILHO, O.O.; NEVES, M.D.M.; RIBEIRO, O.C.S.; DESIMONE, D.; NOGUEIRA, R.A.; AMBROZIO FILHO, F.Artigo IPEN-doc 13033 Low-pressure injection molding processing of AISI T15 high speed steel powders2006 - LIBERATI, JOAO F.; ARAUJO FILHO, OSCAR O.; MONTEIRO, WALDEMAR A.; ESPOSITO, IARA M.; NOGUEIRA, REJANE A.; AMBROZIO FILHO, FRANCISCOArtigo IPEN-doc 14564 Grain size of commercial high speed steel2006 - NOGUEIRA, REJANE A.; ARAUJO FILHO, OSCAR O.; SOUZA, LEONARDO F.M.; LIBERATI, JOAO F.; SALGADO, LUCIO; AMBROZIO FILHO, FRANCISCOThe heat treatment of high speed steel tools consists of austenitizing, quenching and tempering. The size of austenite grains formed during the hardening treatment is an important factor in the final microstructure of the steel, and it also affects properties such as wear resistance and toughness. This paper presents the austenite grain size, matrix composition and hardness of commercial AISI M2, AISI T15, VWM3C and Sinter 23 high speed steels that were austenitized and quenched from five distinct temperatures. This study shows that increase in quenching temperature results in grain growth of steels such as AISI M2 and VWM3C, obtained by the conventional method (cast to ingot and worked). The P/M Sinter 23 high speed steel showed a slight grain growth (about 10%). This effect was not observed in AISI T15 obtained by the powder metallurgy process.