IVAN KORKISCHKO
5 resultados
Resultados de Busca
Agora exibindo 1 - 5 de 5
Artigo IPEN-doc 28365 Three-dimensional CFD modeling of H2/O2 HT-PEMFC based on H3PO4-doped PBI membranes2021 - PANESI, A.R.Q.; SILVA, R.P.; CUNHA, E.F.; KORKISCHKO, I.; SANTIAGO, E.I.A complete non-isothermal model of a HT-PEMFC setup using a PBI/ H3PO4 membrane was developed, modeled, and solved using COMSOL Multiphysics. Polarization curves were simulated and compared to the corresponding experimental data. In this work, a serpentine flow field and an active area of 5 cm2 have been implemented in a computational fluid dynamics (CFD) application. The model predicts water vapor transport, mass concentration of H3PO4, temperature, and membrane current density distribution. In this model, the anode feed is pure hydrogen, and oxygen is introduced at the cathode side. The heat transfer model was coupled with the electrochemical and mass transport; a particular heating configuration is investigated for temperature distribution, emphasizing the membrane. The models showed consistency and were used to investigate the behavior of H3PO4 concentration and all transport characteristics. The concentration of phosphoric acid decreases with increasing temperature and relative humidity and the diffusive flux of water vapor increases with the decrease of the operating voltage. Two different configurations of inlet and outlet flow channels were analyzed and the results were compared.Artigo IPEN-doc 26753 Modeling and parametric analysis of PEM fuel cells using computational fluid dynamics2019 - PANESI, RICARDO; BERUSKI, OTAVIO; KORKISCHKO, IVAN; OLIVEIRA NETO, ALMIR; SANTIAGO, ELISABETEThis paper presents a parametric investigation of PEMFC electrochemical models employing computational fluid dynamics (CFD) technique and aims to determine the relative importance of each parameter on the modeling results. A compatible and systematic mathematical model is developed in order to study the effect of these parameters. The model is applied to an isothermal, steady state an single phase to observe the main results by a polarization curve. The results compare well with the experimental polarization data obtained at 80 ºC for ohmic and activation regions. The best match with the experimental data is obtained when the specific active surface area of the catalyst layer is 700 cm2/mg and electrolyte conductivity of 8 S/m.Artigo IPEN-doc 25825 Spatially resolved oxygen reaction, water, and temperature distribution2019 - LOPES, THIAGO; BERUSKI, OTAVIO; MANTHANWAR, AMIT M.; KORKISCHKO, IVAN; PUGLIESI, REYNALDO; STANOJEV, MARCO A.; ANDRADE, MARCOS L.G.; PISTIKOPOULOS, EFSTRATIOS N.; PEREZ, JOELMA; FONSECA, FABIO C.; MENEGHINI, JULIO R.; KUCERNAK, ANTHONY R.In situ and ex situ spatially-resolved techniques are employed to investigate reactant distribution and its impacts in a polymer electrolyte fuel cell. Temperature distribution data provides further evidence for secondary flows inferred from reactant imaging data, highlighting the contribution of convection in heat as well as reactant distribution. Water build-up from neutron tomography is linked to component degradation, matching the pattern seen in the reactant distribution and thus suggesting that high, non-uniform local current densities shape degradation patterns in fuel cells. The correlations shown between different techniques confirm the use of the versatile reactant imaging technique, which is used to compare commonly used flow field designs. Among serpentine-type designs, the single serpentine is superior in both equivalent current density and reactant distribution, showing large contributions from convective flow. On the other hand, the interdigitated design is shown to produce larger equivalent current densities, while showing a somewhat poorer reactant distribution. Considering the correlations drawn between the techniques, this suggests that the interdigitated design compromises durability in favour of power output. The results highlight how established techniques provide a robust background for the use of a new and flexible imaging technique toward designing advanced flow fields for practical fuel cell applications.Resumo IPEN-doc 25562 Modeling, simulation and shape optimization of a proton exchange membrane fuel cell using computational fluid dynamics2018 - KORKISCHKO, IVAN; SANTIAGO, ELISABETE I.; CARMO, BRUNO S.; FONSECA, FABIO C.This paper presents the modeling, simulation and optimization of a single channel proton exchange membrane fuel cell (PEMFC) using computational fluid dynamics methods. The shape optimization of the cross section of the flow channels was employed to improve the electrical performance of the fuel cell. The minimization of the standard deviation of the current density on the longitudinal mid-plane of the membrane was the objective function of the single-objective optimization problem, the upper and lower widths of the flow channels were the control variables and a cross-section area restriction was imposed. The optimized flow-channel PEMFC presented improved electrical performance, with higher current and power densities and a more uniform current density distribution than the rectangular flow channel. It is also expected that a more uniform current distribution improves the durability and water management of the fuel cell.Artigo IPEN-doc 24378 Shape optimization of PEMFC flow-channel cross-sections2017 - KORKISCHKO, I.; CARMO, B.S.; FONSECA, F.C.This paper presents the modeling, simulation and optimization of a single channel proton exchange membrane fuel cell (PEMFC) using computational fluid dynamics methods. The shape optimization of the flow-channels was employed to improve the electrical performance of the fuel cell. The maximization of the current density was the objective function of the single-objective optimization problem, the upper and lower widths of the flow channels were the control variables and a cross-section area restriction was imposed. The optimized flow-channel PEMFC presented improved current generation characteristics, showing higher current and power densities and a more uniform current density distribution than the rectangular flow-channel.